drag

GEN 6 CAMARO

Conquer the quarter-mile

Chevrolet Performance offers a lineup of parts designed and developed to help improve the launch and traction attributes of your Camaro SS on the drag strip. These parts have seen extreme testing and validation in our Drag Race Development Program, which continues to explore the quarter-mile capability of the sixth-gen Camaro.

Camaro SS extreme validation standards:
400+ passes at 600+ horsepower
60-foot time of 1.433 seconds
Eighth-mile time of 6.739 seconds
Quarter-mile time of 10.569 @ 127.8 MPH  

6.2L Cold Air Intake System – Race Filter

When maximum air flow is all you need, this Cold Air Intake System Race Filter has you covered. Designed for the Camaro SS drag racer, this high-flow dry media race filter provides up to a 51% reduction in restriction at 350 g/sec (compared to the production Camaro LT1 Air Induction System) for the ultimate off-road drag strip performance. Requires Cold Air Intake System (P/N 84329125).

PART NO. 84355716

American Racing Headers

Chevrolet Performance has partnered with American Racing Headers to create a licensed header kit for Camaro. These headers feature 3/8-inch thick flanges with TIG-welded and hand-ported inlets, along with a 1-7/8-inch tube routing that maximizes performance and fit. Designed and manufactured in the USA with USA-sourced 304 stainless steel, these headers are intended exclusively for use in competition vehicles that will only be driven on a track or off-road course.

PART NO. CAV8-161783000LSNC

Rear Small Brake System

The right tires can help put the power to the pavement. Expand your wheel and tire choices by switching to a smaller rear brake system. This brake system decreases the rotor diameter to 315 mm (from the standard 339 mm on SS). This allows for the use of wheels as small as 16 inches (always verify fit). High-performance, semi-metallic brake pads are included to maintain a confident brake feel.

PART NO. 84396515

WELD Racing Rear Drag Wheel

Chevrolet Performance has teamed up with WELD Racing to create a 16-inch x 10-inch racing wheel. Chevrolet Performance engineers provided the proper offset and brake clearances, while WELD Racing optimized the wheels to be as light as possible. The result is a fully vetted drag racing wheel that will fit perfectly on your sixth-generation Camaro.

PART NO. 88B-610SB-GM

High-Stall Torque Converter System

This High-Stall Torque Converter is ideally matched to LT1 powertrain to provide up to 45% increase in stall speed over the standard unit, resulting in consistent lower 60-foot times and overall E.T.’s. This system is intended exclusively for use in competition vehicles that will only be driven on a track or off-road course, and provides the same quality-engineered, torque converter clutch and torque ratio linearity you’ve come to expect from your Chevrolet, while delivering the added performance you crave at the track.

Please note: The ultimate stall speed achieved will depend on the extent of engine modifications, torque management, tire selection and track surface conditions.

PART NO. 24290897

ZL1 1LE Spec Solid Rear Cradle Mounts

These ZL1 1LE Spec Solid Rear Cradle Mounts are constructed from 6061-T6 aluminum and machined from billet. They replace your vehicle’s standard rubber bushings and add rigidity while reducing suspension compliance for drag strip or track driving applications.

PART NO. 84341929

ZL1 Spec Heavy-Duty Halfshaft System

For racers looking for halfshafts capable of carrying up to 5,000 lb.-ft. of torque on each side, round after round. This system was designed for Camaro SS drag racers and includes both right and left halfshafts, washer and bolt assemblies, hub nuts, and replacement exhaust gasket and clamp for a bolt-on and race solution.

PART NO. 84398126

ZL1 Spec Heavy-Duty Propshaft System

With increased power and torque, seasoned Camaro drag racers know they need heavy-duty driveline equipment to put the power to the ground, round after round. Capable of carrying up to 4,000 lbs.-ft. of torque, this system ships complete with the front flex coupler nuts and bolts, center bearings bolts, rear flex coupler nuts and bolts, the complete ZL1 propeller shaft assembly, and replacement exhaust gasket and clamp for a bolt-on drag strip solution.

PART NO. 84398125


Subscribe to the Chevy Performance enthusiast monthly newsletter.


Check out Chevrolet Performance product releases, future car builds, and more.

Connect


Connect with Chevy Performance.

Unless specifically noted to the contrary herein, vehicles equipped with Chevrolet Performance Parts may not meet Federal Motor Vehicle Safety Standards and emissions regulations and should not be operated on public roads. Chevrolet Performance customers are responsible for ensuring their use of Chevrolet Performance complies with applicable federal, state, and local laws, regulations, and ordinances. Many parts intended for racing or other “off-highway” use are not designed or tested for crashworthiness or to meet the safety needs of the motoring public, and may adversely affect the original intended performance or handling characteristics of the vehicle. These parts are designed and intended to be used with experts supervising their installation and use, to help assure the proper and safe operation of the vehicle.

  • Validation results were achieved using the Chevrolet Performance Parts found on this page installed on the 2017 Chevrolet Camaro SS shown.

  • The parts listed on this site are intended for installation in competition vehicles for operation in drag racing applications only. By “competition vehicles,” GM means vehicles (i) used exclusively for competitions organized and sanctioned by a local or private body and (ii) not designed for use on public streets or highways. Consumers are strongly advised not to install parts accompanied by this warning on vehicles that will be driven on public roads.  They have not been designed or tested for crashworthiness or to meet the safety needs of the motoring public, and they may not meet the full durability requirements that Chevrolet validates for its street legal, production vehicle components.
    U.S. federal and state, and Canadian law prohibit an automobile manufacturer or dealer from removing, modifying or rendering inoperative any part installed on a motor vehicle in compliance with an applicable Federal Motor Vehicle Safety Standard. Further, U.S. federal and state, and Canadian law prohibit any person from knowingly removing, modifying, or making inoperative, or causing someone to remove or render inoperative, or otherwise tampering with, any part or element of design installed in compliance with motor vehicle emission standards on a motor vehicle or nonroad vehicle, or otherwise modifying any required emission and noise control system.
    Unless specifically noted to the contrary herein, vehicles equipped with Chevrolet Drag Racing Parts may not meet Federal Motor Vehicle Safety Standards and should not be operated on public roads. Installation or use of these parts on a vehicle operated on public streets or highways is also likely to violate U.S., Canadian, and state and provincial laws and regulations relating to motor vehicle emissions. U.S. federal and state, and Canadian provincial agencies have the authority to administer substantial monetary penalties against individuals and companies who do not comply with these laws. Chevrolet Performance customers are responsible for ensuring their use of Chevrolet Drag Racing Parts complies with applicable federal, state/provincial and local laws, regulations and ordinances, and for ensuring that modified vehicles are operated in a manner that complies with applicable laws.
    The use of these components in a GM vehicle may adversely affect the original intended performance or handling characteristics of the vehicle. These parts are designed and intended to be used with experts supervising their installation and use, to help assure the proper and safe operation of the vehicle. While these components themselves are warranteed against defects in workmanship or materials for 12 months / unlimited miles, the use of certain Chevrolet Drag Racing Parts in a GM vehicle may result in the failure of other components or systems in the vehicle, which would not be covered under the New Vehicle Limited Warranty.  For Drag Racing Parts in this designated with an asterisk (*), installation of such parts may void part or all of the New Vehicle Limited Warranty.  Otherwise, vehicles do retain their New Vehicle Limited Warranty coverage with Chevrolet Performance components installed by an authorized GM Dealer or qualified Independent Service Center.

  • Accessories installed by an authorized GM Dealer will be covered, parts and labor, for the longer of the following: a) 12 months/12,000 miles (whichever comes first), or b) the balance of the applicable portion of the New Vehicle Limited Warranty. See your dealer for details. Accessories (i) purchased at a dealership (but not installed by a dealer), (ii) shipped directly to a customer, or (iii) not requiring installation, will receive the standard GM Dealer Parts Warranty of 12 months from the date of purchase, parts only, regardless of miles. Associated Accessories are provided by independent companies and are not warranted by GM or its dealers. The independent company providing an Associated Accessory, rather than GM, is responsible for the safety and quality of Associated Accessories. For more details on exhaust system compliance with local and state noise ordinances, trailer weight rating calculations, cargo limitations, load trailer weight capacities and possible installation charges incurred with certain accessories, contact your local GM Dealer.

  • The Manufacturer's Suggested Retail Price excludes destination freight charge, tax, title, license, dealer fees and optional equipment. Click here to see all Chevrolet vehicles' destination freight charges.